KALPOXY® Coatings

KALPOXY high build epoxy coatingsKALPOXY® 100% solids high build epoxy coatings are based on a unique blend of liquid epoxy polymer and aliphatic polyamine curing agents, which are able to displace water from wet surfaces in order to make a permanent bond. The formulation is solvent-free to ensure safety and maximum technical performance. Kevlar®* fibers are incorporated for reinforcement and viscosity management to achieve high application rates - even underwater! View our comparison guide.

*Kevlar is a trademark of E.I. Dupont de Nemours Co.

  • KALPOXY® 255 - Formulation designed for tough Corrosive/Errosive Conditions. Exposure to water or high humidity during curing has no adverse affect on coating. Available in formulations for spray or Roller/Trowel applications.
  • KALPOXY® 258 - Based on a unique blend of liquid epoxy polymer and aliphatic polyamine curing agents, which is able to displace water from wet surfaces in order to make a permanent bond. The formulation is solvent-free to ensure safety and maximum technical performance.
  • KALPOXY® 560 - Solvent free formulation which is able to displace water in order to make a permanent bond to all substrates with minimal substrate preparation.
  • KALPOXY® 290 - Same as our 560 product but designed for application with roller, brush or conventional spray equipment. Complete with UV protective additive to eliminate chalking.
  • KALPOXY® 565 - Same as our 258 product but the formulation is uniquely field-friendly, non-hazmat and supplied in the most preferred 1/1 by volume mixing ratio. Uses advanced low toxicity ingredients in a high build brushable/rollable product.
  • KALPOXY® 568 - Based on a unique blend of liquid epoxy polymer, toughening resins and aliphatic polyamine curing agents and is able to displace water from wet surfaces in order to make a permanent bond. The formulation is solvent-free to ensure safety and maximum technical performance – even underwater!
  • KALPOXY® 595 - Low friction, super tough, solvent-free epoxy coating, when cured it is hard but flexible. Formulation promotes sliding with no contamination. Suitable for covering concrete and steel surfaces and uniquely designed to be
    abrasion and impact resistant.
  • KALPOXY® 254 - Solvent free formulation able to displace water from wet surfaces in order to make a permanent bond. Ensures safety and maximum technical performance under the most adverse conditions including exposure to most industrial chemicals such as acids, alkalis and hydrocarbons.
  • KALPOXY® Almond 2001 - Aliphatic ployamine cured liquid epoxy polymer “nuclear quality” coating. Self-priming and approved for some Service Level 1 nuclear applications. This solvent-free formula has been optimized for application by plural component airless spray above water.

KALPOXY® Coatings Guide
 
Steel Surfaces
Concrete Surfaces
Maximum Operating
Temp.
Brushable/
Rollable
Sprayable
Moisture Tolerant
(Cure Under Water)
Surface
Prep
Required
KALPOXY 560
180° F
SSPC-SP3
KALPOXY 290
180° F
SSPC-SP3
KALPOXY 255
180° F
SSPC-SP6
KALPOXY 254
180° F
SSPC-SP6
KALPOXY 258
180° F
SSPC-SP2
KALPOXY 565
180° F
SSPC-SP3
KALPOXY 568
180° F
SSPC-SP3
KALPOXY 595
180° F
SSPC-SP6
KALPOXY
Almond 2001
400° F
SSPC-SP6


KALFIX® Adhesives

  • KALFIX adhesiveKALFIX® 911 - “5-Minute” epoxy filler with extreme adhesion even to underwater surfaces. Used primarily as a pressure-transfer filler under high pressure pipeline repair composites.
  • KALFIX® 913 - Longer pot life version of 911. “15-Minute” epoxy filler with extreme adhesion even to underwater surfaces. Supplied in a standard white base, which is mixed with an equal volume of gray curing agent to yield a lighter gray when thoroughly mixed. The formula is uniquely field-friendly using advanced low toxicity ingredients and can be shipped “Non-Regulated” by USDOT, IATA and IMO.
  • KALFIX® 563 - “45-Minute” curing version of KALPOXY 560 for pipeline coating or cold weather use.
  • KALFIX® 206 - Combination liquid epoxy resin and a special high temperature curing agent. Although this epoxy has a high heat distortion, is still cures to a hard and dust-free condition at normal temperatures.